EasyPSV® Printable

NEW PRODUCT!  EasyPSV goes printable!

EasyPSV Printable is 100 Microns / 3.9 Mils and is a PVC composition.

EasyPSV Printable Applies To:

  • Glass/Mirror
  • Wood
  • Plastic
  • Metal
  • Ceramic

EasyPSV Printable is a PVC-based material and not CPSIA certified.

Effacer
Qty:
UGS : ND Catégorie :

Description

EasyPSV Printable is Siser’s version of a printable adhesive vinyl. Like all EasyPSV products, this material is for use on hard surfaces without the need for heat! EasyPSV is gloss finish. EasyPSV is a permanent tack adhesive and compatible with solvent, eco-solvent, and latex printers. Much like it’s heat transfer vinyl cousin it is not recommended for use with an inkjet, laser, or sublimation printer.

Cricut Explore Air: Blade: AutoBlade, Standard  Setting: Vinyl
Cricut Maker: Blade: AutoBlade, Fine-Point  Setting: Vinyl
Brother Scan N Cut DX: Blade: Standard, 3  Cut Speed: 1  Cut Pressure: 2
Silhouette Cameo 4: Blade: AutoBlade, 2  Material: Vinyl, Glossy  Force: 7  Speed: 8
Roland GX/GS-24: Blade: 45°  Gram Force: 80-110  Offset: .250  Speed: 30-50 cm/s
Graphtec: Blade: 45°  Gram Force: 9  Tool: CBO9U+0  Speed: 30 cm/s
US Cutter Titan 2 & 3: Blade: 45°/60°  Gram Force: 50-55  Speed: 300 mm/s  **Blade Advancing Varies
Mimaki CG-60SR III: Blade: 45° Gram Force: 50  Offset: 30  Speed: 20-30 cm/s
Brother Scan N Cut: Blade: Standard, 3  Cut Speed: 1  Cut Pressure: 2

The specifications listed are suggested starting points that may need to be adjusted according to blade, cutting strip and cutting mat wear. Always perform a test cut prior to cutting designs.

*Craft cutters were evaluated using cutter-specific standard grip cutting mats.

Informations complémentaires

Poids ND
Dimensions ND
Largeur de rouleau

20, 29.5", 54" and 59"

Longueur du rouleau

1 verge, 5 verges, 10 verges, 25 verges, 50 verges

Application instructions
• Set heater/dryer to 113°F/45°C
• Print, cut, and weed design (DO NOT reverse/mirror your design)
• If printing heavy saturation ink, allow to dry 1 hour before cutting
• Mask your design using the EasyPSV Application Tape
• Place the application tape on your desired object and burnish with a squeegee to fully adhere the design
• Lift the application tape and EasyPSV away from the paper liner to expose the removable adhesive
• Place the application tape on your desired object and burnish with a squeegee to fully adhere the design
• Gently peel away the application tape, leaving just your EasyPSV design on the object

Surface prep instructions
For best adhesion, remove any dirt, dust, grease, etc to prepare the surface you want to decorate with EasyPSV. The following cleaning method is not recommended for porous surfaces such as unfinished/untreated wood. It is recommended that all other surfaces be spot tested with care before cleaning the entire application area.

Non-porous surfaces can be cleaned with a mix of approximately 2 parts water and 1 part isopropyl alcohol (70% or higher for best results) or non-amonia based window cleaner. Use a microfiber or lint free towel to clean the application area with the mixture. Paper towel is not recommended since it will leave behind small bits of paper that can become trapped under the EasyPSV during application. Ensure the area is completely dry before applying.

*The cleaning method outlined above is subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

 

Removal instructions
If the EasyPSV peels up, but leaves an adhesive residue use an adhesive remover to clean the area. If the EasyPSV is stubbornly sticking, the heat from a hair dryer or garment steamer can help loosen the adhesive. However, heating is not recommended for glass due to possible shattering. To remove Permanent EasyPSV from glass, saturate the decal with soap and water. Cover with plastic wrap and let sit for a few hours before attempting to remove. An adhesive remover may still be required to clean all adhesive from the surface after removing the EasyPSV.

*The removal instructions outlined above are subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

Not for use on walls or for temporary applications. Not recommended for use near flame/heat source. Not microwave or dishwasher safe.

514 664-2013 info@grafikexperts.com 2000, St-Regis Dorval, QC Canada