EasyPSV® Removable Holographic

Stick it, Switch it, Smile!

Create worry-free décor that can be changed repeatedly using EasyPSV Removable Holographic by Siser.

EasyPSV Removable Holographic Applies To:

  • Glass/Mirror
  • Wood
  • Plastic
  • Metal
  • Ceramic
Clear
SKU: N/A Category:

Description

This temporary pressure sensitive vinyl takes the guesswork out of decorating. You don’t have to wonder if the adhesive vinyl will leave a gluey mess behind, or even worse, take some of the wall with it! EasyPSV Removable Holographic comes off cleanly and quickly without any special tools or solvents for care free customizing!

While EasyPSV Removable lasts 2-3 years, you can choose to change it up at any time, and with a stylish matte finish who wouldn’t? Plus EasyPSV Removable Holographic even includes Blackbpardboard! Use this black, textured vinyl to turn any hard surface into a writable chalkboard that’s compatible with soft chalk, standard chalk, and chalk ink markers. But the best part is, you can layer EasyPSV Permanent on top of EasyPSV Removable Holographic for temporary decals that have virtually endless color and finish combinations!

Cricut Explore Air: Blade: AutoBlade, Standard  Setting: Vinyl
Cricut Maker: Blade: AutoBlade, Fine-Point  Setting: Vinyl
Brother Scan N Cut DX: Blade: Standard, 3  Cut Speed: 1  Cut Pressure: 1
Silhouette Cameo 4: Blade: AutoBlade, 2  Material: Vinyl, Glossy  Force: 7  Speed: 8
Roland GX/GS-24: Blade: 45°  Gram Force: 80-110  Offset: .250  Speed: 50 cm/s
Graphtec: Blade: 45°  Gram Force: 9  Tool: CBO9U+0  Speed: 50 cm/s
US Cutter Titan 2 & 3: Blade: 45°/60°  Gram Force: 50-55  Speed: 180 mm/s  **Blade Advancing Varies
Brother Scan N Cut: Blade: Standard, 3  Cut Speed: 1 Cut Pressure: 1

The specifications listed are suggested starting points that may need to be adjusted according to blade, cutting strip and cutting mat wear. Always perform a test cut prior to cutting designs.

*Craft cutters were evaluated using cutter-specific standard grip cutting mats.

Additional information

Weight N/A
Dimensions N/A
Roll Width

20"

Roll yards

1yd, 5yd, 10yd, 25yd, 50yd

Application instructions
• Place EasyPSV with the liner side down and cut your design. (DO NOT reverse/mirror your design)
• Weed excess vinyl
• Remove the application tape’s paper liner. Place tape on top of EasyPSV and burnish with a squeegee
• Lift the application tape and EasyPSV away from the paper liner to expose the removable adhesive
• Place the application tape on your desired object and burnish with a squeegee to fully adhere the design
• Gently peel away the application tape, leaving just your EasyPSV design on the object

Surface prep instructions
For best adhesion, remove any dirt, dust, grease, etc to prepare the surface you want to decorate with EasyPSV. The following cleaning method is not recommended for porous surfaces such as unfinished/untreated wood. It is recommended that all other surfaces be spot tested with care before cleaning the entire application area.

Non-porous surfaces can be cleaned with a mix of approximately 2 parts water and 1 part isopropyl alcohol (70% or higher for best results) or non-amonia based window cleaner. Use a microfiber or lint free towel to clean the application area with the mixture. Paper towel is not recommended since it will leave behind small bits of paper that can become trapped under the EasyPSV during application. Ensure the area is completely dry before applying.

*The cleaning method outlined above is subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

 

Removal instructions
Clean removability guaranteed for 2 years. Later removal may require an adhesive remover to clean all the adhesive from the surface. If the EasyPSV is stubbornly sticking, the heat from a hair dryer or garment steamer can help loosen the adhesive. However, heating is not recommended for glass due to possible shattering. To remove Permanent EasyPSV from glass, saturate the decal with soap and water. Cover with plastic wrap and let sit for a few hours before attempting to remove. An adhesive remover may still be required to clean all adhesive from the surface after removing the EasyPSV.

*The removal instructions outlined above are subject to modification and not always suitable for every substrate.

The purchaser should independently determine with their own testing to use this method or not on a case by case basis.

Not recommended for use near flame/heat source. Not microwave or dishwasher safe

514 664-2013 info@grafikexperts.com 2000, St-Regis Dorval, QC Canada